MAVERICK BOND Industrial adhesive is a high quality product of modern chemistry. It represents a sensational development in the field of adhesive technology.
It is based on an alpha-Cyanoacrylate ester and utilizes an anaerobic process to form incredible bonds in seconds.
MAVERICK BOND is the result of many years of research and professional testing. For manufacturing reasons it is almost impossible to obtain a higher degree of distillation.
MAVERICK BOND Industrial adhesive is a high quality product of modern chemistry. It represents a sensational development in the field of adhesive technology.
It is based on an alpha-Cyanoacrylate ester and utilizes an anaerobic process to form incredible bonds in seconds.
MAVERICK BOND is the result of many years of research and professional testing. For manufacturing reasons it is almost impossible to obtain a higher degree of distillation.
MAVERICK BOND Industrial adhesive is a high quality product of modern chemistry. It represents a sensational development in the field of adhesive technology.
It is based on an alpha-Cyanoacrylate ester and utilizes an anaerobic process to form incredible bonds in seconds.
MAVERICK BOND is the result of many years of research and professional testing. For manufacturing reasons it is almost impossible to obtain a higher degree of distillation.
MAVERICK FILL – chemical weld. | ||||||||
|
||||||||
|
MAVERICK CLEAN – acetone based cleaner.
Polished, smooth or glazed surfaces should be cleaned thoroughly otherwise and residual dust or contaminants can interfere with the resulting bond. Alternatively, the can be used to clean MAVERICK BOND nozzles, to clean off any excess glue or break the bond in case of mistakes.
Maverick 4 Poly Pack consists of 1 x Bond 20g, Fill 20g, Prime 10ml and Clean 20ml
Maverick 4 Home Pack consists of 1 x Bond 20g, Fill 20g, Acelerator 10ml and Clean 20ml
Maverick Professional Set consists of 1 x Bond 20g, Fill 20g, Clean 20ml, Accelerator 10ml, Prime 10ml, Aqua & Steel in a portable heat resistant protective casing.
Homopolar synthetics such as Polyethylene (PE) or Polypropylene (PP) without pretreatment cannot be glued permanently with any glue. Other materials, such as Teflon and some polyurethane, also encounter similar difficulties.The surface energy of these polyofines ranges around 30mN/m, which leads to problems in moistening these materials with the glue. In practice, however, it is just these materials that are frequently employed because of their excellent properties. Still, when glued together, the results were not satisfactory or it was not possible at all.
Previously, adhesion on such plastics could only be successful done by heat welding. MAVERICK PRIME now offers a practical possibility to gain, by simple means of a high degree of tenacity when gluing homopolar materials with cyanoacrylatic glues. The low-viscous solution is applied to the material and, after the non-polluting dissolvent evaporates in 20-60 seconds, MAVERICK BOND is applied. The joining can be performed by fitting the parts together and exerting pressure for a short moment. After the hardening, which may take between 2 to 6 hours depending on the combination of materials – generally allow a minimum of few hours – you will often gain combined tension and shear resistance of more then 6N/mm. |
|||||||||||||||||||||
Storage time between MAVERICK PRIME ACTIVATOR treatment and bonding | |||||||||||||||||||||
![]() |
|||||||||||||||||||||
|
MAVERICK ACCELERATOR – aid when glueing porous materials.
The MAVERICK ACCELERATOR has 2 primary functions.
1. When attempting to glue porous materials – such as porcelain, ceramics, natural woods, terracotta, concrete or leather – the actual surface area available for bonding is fragmented thus limiting surface contact thereby reducing the strength of the bond.
The MAVERICK ACCELERATOR acts as a sealant and by increasing the surface contact, allows for better and stronger bonding on porous materials.
2. The anaerobic nature of the MAVERICK BOND requires the absence of air to form bonds. Thus porous materials make such processes difficult – requiring additional drying time. Applying the MAVERICK ACCELERATOR significantly reduce the bonding time on such porous materials.
In addition, the MAVERICK ACCELERATOR reduces glue loss resulting from the porous materials absorbing or soaking up the glue.
The MAVERICK ACCELERATOR can also be used on non-porous materials. Bonding polished surfaces such as glass, tiles and various metals can be aided by the MAVERICK ACCELERATOR by ensuring a clean non-slippery surface for the adhesive to work on.
Apply the MAVERICK ACCELERATOR via the brush tips in the bottle to one side of the material and the MAVERICK BOND on the opposite side. DO NOT apply both products on the same side. In cases whereby 2 different materials are being glued, apply the ACCELERATOR to the more porous material.
It is not necessary to apply the Maverick Accelerator on non-porous materials.
Porous materials CAN BE glued without the Maverick Accelerator but if so, or for those who do not have the Accelerator, allow more time for the Maverick Bond to form bonds.
Where Maverick Accelerator is not available, apply the glue then apply pressure to the area for about 5 seconds. Then allow for it to set for a several minutes before you test the bonding strength – time dependent on the materials involved.